02-06-2018 05:13 PM
I have a job that a client is now asking for the option to print my section dividers as Tabbed dividers. My plan to run this job was to initially run the guts of the book as 2-up Gang then I'll trim in half for offline finishing.
I know if they do want to go with tabs that I'll have to run the tabs separately and have them inserted manually into the book. How do I set up a page in Indesign (mac) and then print onto Tabs stock?
Solved! Go to Solution.
02-06-2018 06:33 PM
Entirely depends on what you do in the driver and the file.
If the file is layed out as 9*11 you just print it onto tab stock like the tabs don't exist.
If the file is layed out as Letter you need to turn on Image shift in finishing.
If the tabs are in the job and letter sized you do exceptions with the tab shift enabled
02-07-2018 09:46 AM - edited 02-07-2018 09:46 AM
I have complete control on design for this document and the dividers will have quite a bit of colour on them (and hopefully I can get text aligned properly to print on the tab. I would choose to set up the tabbed pages as 9x11 inch as that just seems so much easier.
I need to produce 50 books and there will be either 2-sets of 5-bank tabs or a custom 10-bank set created. Should I load the stock into Tray 5 and which option should I select for exit. I'd assume I don't want to be 'flipping' the tabbed stocked within the printer.
02-07-2018 12:23 PM
Tray 5, tabs to the left, reverse order tabs (I believe)
It won't let you duplex them if programmed as tab stock because it will cause jams when the tab goes in front. If set as 9*11 hvyweight you may get away with duplexing. Exit doesn't matter at all if you are inserting into the job later.
02-21-2018 12:49 PM - edited 02-21-2018 12:50 PM
Joe, I'm now at the point where I'm attempting to print onto actual tab stock and not my test stock (didn't have diecut tabs). When I run pages through my C60 the printer jams when the printed tab reaches a certain point in the machine. I have set up my pages for the tabs and am printing a 9x11 page design to a 9x11 sheet? I've attached a picture to show where it jams.
02-21-2018 01:24 PM
I'm more of a software guy so jams are a long way off of my specialty.
My guess is that it doesn't jam, it stops and declares a jam, and that it is the 3rd of 5 bank tabs (or whatever the middle is of your banks) and it is caused when a sensor sees the middle tab and thinks the stock is .5 inches farther into the machine than it is (The sensor sees the tab because the sensor is in the middle, the tab isn't there for 4 out of the 5 banks)
I'm not sure if it is something that can be fixed in all honesty, sometimes you get away with it, sometimes you don't. You may have to adjust to Letter size, or run the center tabs as a separate job and skip them on the actual run.
02-21-2018 01:31 PM
I checked my settings and currently I have the paper type to Heavyweight 1 and just noticed that there are options for Tabs. I'm now thinking that I sould change that value to Tabs and test again. (Perhaps that setting disables the sensor)?
02-21-2018 01:36 PM
It doesn't disable the sensor, but it does allow it to compensate for it.
The problem with using it here is that it will force the tray to be 8.5*11, not 9*11 (The tab is the .5 inch.)
So you may need to impose an image shift to put the text on the tab, and by the look, you are printing more than just on the tab, so it may look odd.
02-21-2018 01:45 PM