Showing results for 
Search instead for 
Do you mean 
Reply
Member
Posts: 29
Registered: ‎06-01-2016

printing on #10 envelopes on the C70 EX-i

Hello,

please how do i print on envelopes using the by-pass tray on the C70 with an External fiery?

Is this even possible, cause on the by-pass tray it shows a cross mark?

Please assist.

Ever grateful for all the solutions and knowledege obatined on here.

Well appreciated.

M.A

Analyst Nation Moderator
Posts: 4,516
Registered: ‎11-25-2013

Re: printing on #10 envelopes on the C70 EX-i

It's an odd setup to say the least.

 

Tray 5 clearly has a no envelopes logo (Note, the envelope must be upside down, 180 degrees from how it is pictured)

 

1.gif

 

so I am not sure why the CEIG would have steps that use it.

 

I set mine as custom, 4.1*9.5 HVY 2, Flap closed because that's how I roll.

 

2.jpg

 

 

The envelope must be SEF (Tray can't take the LEF sizes) and upside down, Clockwise Rotation  box in Word does not do a thing to the printout.

 

3.gif

 

Here is the driver itself

 

Capture.GIF

 

But there are many ways to get it to print, you need to find the best that works for you. Envelopes are a real PITA, because the dimensions change often, especially if you do it flap open, because the flap can change the dimensions by a lot.

 

 

Please be sure to select "Accept Solution" and or select the thumbs up icon to enter Kudos for posts that resolve your issues. Your feedback counts!

Joe.
Member
Posts: 29
Registered: ‎06-01-2016

Re: printing on #10 envelopes on the C70 EX-i

tried all the steps but didnt get it to work.

But thanks

Analyst Nation Moderator
Posts: 4,516
Registered: ‎11-25-2013

Re: printing on #10 envelopes on the C70 EX-i

[ Edited ]

Then archive the job on the Fiery , make it a zip file and link it here, I will put it on mine and find out where it went wrong.

 

You never give details , so it makes it very hard to give you clear directions, like if you were to state that it isn't working, and it fails (turns red) in the Fiery (Command Workstation) then I could tell you the likely issue is that you tried to print it face down, which would not have been supported, and you could fix it by picking face - up instead.

 

 

tried all the steps but didnt get it to work.

There are about 15 points of failure, narrow down your statements.

Please be sure to select "Accept Solution" and or select the thumbs up icon to enter Kudos for posts that resolve your issues. Your feedback counts!

Joe.
Member
Posts: 29
Registered: ‎06-01-2016

Re: printing on #10 envelopes on the C70 EX-i

sorry for the trouble,it was a simple step as your shots show.yeah on the fiery part is shows

printer status-load 4.1x9.5 inch

envelope white in tray 5(byspass)

more of a network person .

Thanks

Analyst Nation Moderator
Posts: 4,516
Registered: ‎11-25-2013

Re: printing on #10 envelopes on the C70 EX-i

They didn't follow my directions then, at no point anywhere did I program the printer, the application, or the driver with an envelope, so it is impossible for anything to request one. My settings were using Hvyweight 2.

Please be sure to select "Accept Solution" and or select the thumbs up icon to enter Kudos for posts that resolve your issues. Your feedback counts!

Joe.
Member
Posts: 29
Registered: ‎06-01-2016

Re: printing on #10 envelopes on the C70 EX-i

Capture.JPG

 

this what she sent me,she said she followed it step by step.

Sorry Joe just trying to help our custmer,

like i sadi thank yu for what you do.

Analyst Nation Moderator
Posts: 4,516
Registered: ‎11-25-2013

Re: printing on #10 envelopes on the C70 EX-i

Sure looks like they may need to rotate the paper 90 degrees in tray.

Please be sure to select "Accept Solution" and or select the thumbs up icon to enter Kudos for posts that resolve your issues. Your feedback counts!

Joe.