cancel
Showing results for 
Search instead for 
Did you mean: 
nsitechnology New Member
New Member

Phaser 6510 Transfer Unit Replacement

Jump to solution
Product Name: Xerox Phaser 6510 Transfer Unit Replacement
Operating System: Windows 10 x64

Hi,

One of my customers has a 6510 with a transfer unit that's severed on one side which causes the print to come out marked from it.

I could not find any info on how to disassmble thus was wondering how time consuming replacing it is and difficulty level, not sure it will be worth replacing..

Thank you!

0 Kudos
10 Replies
Community Manager CherylO-Xerox
Community Manager

Re: Phaser 6510 Transfer Unit Replacement

Jump to solution

Hi Nsitechnology,

Thank you for using the Support Forum. Please take a look at the solution for the marks.  If this does not help please consider contacting your support centre for further assistance or to palce a service call. 

Thanks,
CherylO-Xerox
Community Manager

Be sure to click Kudos for those who have helped you.
Select Accept as Solution for posts that have helped to solve your issue(s)!

0 Kudos
nsitechnology New Member
New Member

Re: Phaser 6510 Transfer Unit Replacement

Jump to solution

Hi,

Thank you for your reply but this explains how to find what's the issue but not how to replace the transfer belt..Where can i find a service manual for the phaser 6510?

Thanks,

0 Kudos
gabiene Valued Advisor
Valued Advisor

Re: Phaser 6510 Transfer Unit Replacement

Jump to solution

Hi,

See how to do it in my other post.

 

Gabi

0 Kudos
nsitechnology New Member
New Member

Re: Phaser 6510 Transfer Unit Replacement

Jump to solution

Mine is a Phaser 6510, i read on another post both side mouldings need to come out etc..

In your other post it looks pretty simple, does it apply to the phaser 6510 as well?

0 Kudos
gabiene Valued Advisor
Valued Advisor

Re: Phaser 6510 Transfer Unit Replacement

Jump to solution

Yes, because the WC6515 is MFP and it is 6510 with scanner, practically they have the same base.

nsitechnology New Member
New Member

Re: Phaser 6510 Transfer Unit Replacement

Jump to solution

Sorry for taking your time again, the belt does not come out as easily as that on the Phaser 6510, would you by any chance have access to service manual for this model? I believe i have to take apart both mouldings on each side etc..

Copy Paste from another post:

"Removing both left and right cover, also using a screwdriver is needed on this machine to remove the transfer belt.

After removing the covers, and harness from the belt, unplugging the connector, pivot kit etc."

0 Kudos
gabiene Valued Advisor
Valued Advisor

Re: Phaser 6510 Transfer Unit Replacement

Jump to solution

Do you have an 6510 or 6500? They are different.

0 Kudos
nsitechnology New Member
New Member

Re: Phaser 6510 Transfer Unit Replacement

Jump to solution

I have a Phaser 6510

0 Kudos
gabiene Valued Advisor
Valued Advisor

Re: Phaser 6510 Transfer Unit Replacement

Jump to solution

There are no moulding anywhere, Just the four screws.


1. Open the Waste Cover.
2. Remove the Waste Cartridge,
3. Open the Rear Cover.
4. Release the lever on each of the CRU Drum Cartridges (Y,M,C,K).
Figure 1 Handle Locations on the Transfer Belt Unit

5. Refer to Figure 2 to remove the four screws attaching the Transfer Belt Unit and remove
the Transfer Belt Unit from the rails. Remove only the screws seated against the metal
frame as shown in the figure.

6515 belt.png6515 belt removal.png