cancel
Showing results for 
Search instead for 
Did you mean: 
Tasmania New Member
New Member

Phaser 8200 paper feed error

 

Greetings from Australia

 

I have a problem with an Phaser 8200 DP solid wax printer that was bought brand new in 2003 and has printed about 12000 pages in total. Initially the machine would not feed paper on an intermittent basis, you would get a paper jam error message and there also as part of this failure would be a fairly large clunking noise when it did this, upon removing the paper tray the top sheet would be lifted up over the edge of the tray and pulled forward about half an inch relative to the other sheets, I would usually just carefully replace it and re-insert the tray and continue printing once I cleared the error. This was a minor nuisance when it started doing this every 20-30 sheets or so but with the passage of time over about a year it deteriorated and it now exhibits this error every 2-3 sheets it prints. On top of this once it has failed in this manner about 3-4 times the printer then aborts and also re-boots from scratch like when you first turn on the power to the printer.

 

As far as I can tell it looks like the paper hasn't been pulled forward enough so that the lower feed rollers can grab it, there are no other problems at all other than this, either way the paper is completely undamaged when it does manage to go through the machine and prints normally and also undamaged when it is sitting in the tray as described above when it fails.

 

I rang Fujixerox and asked for their opinion and they said that without having the machine examined by an authorized repair technician it appears that the pick roller may need to be replaced. I then had a look at the roller and cleaned it according to instructions. The roller is not dirty and neither is it slick in texture. It appears undamaged and the surface of the roller has a soft patterned texture that gives me the impression that it would have no difficulty in moving sheets of paper, cleaning it made no difference to this problem whatsoever.

 

Reading further on the internet I formed an impression that the problem may be with a clutch assembly that engages the pick roller at presumably the right time and for the required duration at the start of the printing process until the sheet is caught by the lower feed rollers. I am a bit dubious that this could be the case as the machine is rated for a monthly duty cycle of 85000 pages and we have only put about 12000 pages through in the 8 years we have owned it, however this appears to be the most logical answer to my situation.

 

Could you please advise whether this problem is previously known to you and the solution is what I suspect it to be? Am I looking forward to a simple and relatively cheap repair or one that is going to require things like circuit boards and other more complex parts to be replaced?

 

Thanking you in advance in anticipation of your reply.

 

George

 

 

0 Kudos
3 Replies
Agency Analyst JordanAXAUQE-AA
Agency Analyst

Re: Phaser 8200 paper feed error

Do you have an exact error message from the machine? I can lookup the error codes and check out the Service Manual for you.

Thank you,
Jordan R.
Systems Analyst / Consultant
Fiery Certified Professional

If someone helped you make sure you give Kudos for their efforts! Don't forget to Select Accept as Solution if the reply resolved your issue as it will be able to help others!
0 Kudos
JohnXDPS Frequent Member
Frequent Member

Re: Phaser 8200 paper feed error

Unless you are provided with a specific error/system message off the device its rather difficult to trouble shoot these types of issues.  Due to the age of the device and the nature of this problem I think the FUJI rep advised you wisely to seek out an authorized service tech. 

 

Xerox builds machines so that they last much longer than 12,000 pages and its too bad thats all you got out of it.  Most of my solid ink customers (8400, 8500, 8560, 8570) are ranging from 500-2000 pages per month typically and they usually get 3-4 years without probems that require a service tech on them and then other times I sell someone a device within a couple of months they need a tech.   

 

Xerox recently launched the 8570, and the purpose of mentioning this is that you may be able to purchase a new solid ink device with a warranty for substantially less than what it costs to get onsite service with parts replacement. 

0 Kudos
dlw New Member
New Member

Re: Phaser 8200 paper feed error

I have a similar problem but with a XL2140df copier.  In my case the pick rollers are very smooth and simply slide over the paper -- the paper never moves at all.  Is there any way to clean them so that the proper surface is restored?  If not, I'd like to replace them but I can't find the necessary part(s) on the Xerox website.

 

Thanks.

0 Kudos