HiRe: Xerox Phaser 6510

[George850650-XRXN]

Demo,

I am sorry that you are still having issues with the firmware. I have attached another another link for your review.

https://forum.support.xerox.com/t5/Hardware/Phaser-6510-Stuck-on-quot-Please-wait-quot-after-using-t... 

If this still does resolve your issue please try contacting Xerox Support again.

Here is the contact info for Support in Italy:

Xerox S.p.A.

Registered office: Sesto San Giovanni ( MI) - Viale Edison 110 Sales: 800 660099 Assistance: 02 999 53 428 Monday - Friday 8:30 - 18:00 CET FAX: 02 50989447

I hope this helps.

[Demo]

Non vorrei, come suol dirsi, mettere il dito nella ferita. Ma mi sta capitando una disavventura Kafkiana con questa stampante. Fatto salvo il fatto che il mio errore è stato quello di installare un firmware errato e, di conseguenza, la stampante è diventata inutilizzabile.

Vorrei ripristinarla ma sembra che ciò sia impossibile.

Nonostante i tentativi di aiuto di alcuni volenterosi, sembra che tale stampante sia diventata merce da buttare in discarica.

Il mio ultimo post, che non ha auto risposta, è il seguente: https://forum.support.xerox.com/t5/Printing/Installazione-firmware-errato/td-p/256037

Purtroppo il mio problema è rimasto insoluto. Dovrò acquistare una nuova stampante, e questo mi dispiace, non trovo i soldi per la strada.

[GabiE-Xerox]

Hi,

Most of the issues with non printing jobs and „Offline” messages are from driver settings.

 First check to see if  there is no job in the print queue (delete any job if exist).

 Check the port to be on TCP/IP and not WSD. MS convert the port to WSD. If it is so, click right on the print driver and click on „Printer Properties”, click on „Ports” tab, click on „Add port”, select „Standard TCP/IP port” , click on „New port” and set an IP and in the next window click „Finish”.

After that click again on ''Ports'' tab click on "Configure port" and change from  RAW to LPR, at the Queue name write "lp" and be sure to unchecked "LPR Byte Counting Enable" and "SNMP Status Enabled".

Gabi

[NettaWhy]

My Phaser 6510 keeps saying "offline" whenever I try to print. It is most frustrating when downstairs reps try to print to the printer, which is upstairs, and they have to run upstairs to try to get the printer to work. When I run the troubleshooter, the problem comes back, " turn printer on" but the printer is on already.

How do I fix this???? The printer is only a few months old and already I think I need to replace it.

[rchiu]

I have the similar problem. And the worst is the printer died after 2 months usage.  contacting to support trying to have it fixed.

[kleankutken]

The defective printer was picked up today and another defective printer was delivered in its place.  At least this printer will turn on and off when it is supposed to.  But that is as far as it goes.  The printer does not know what tray it wants to print from.  This one is going back also.

[ether]

This is interesting. I haven't had any issues with the Phaser 6510 and it normally gives good experiences. A replacement should work fine for you.

[CherylO-Xerox]

Hi Kleankutken,

Thank you for using the Support Forum and I apologize for the frustration you are experincing because of the printer.  Since it is brand new requesting a replacement may be the best bet.  But make sure that you are plugging the machine into a dedicated outlet, no power strip or surge protector.  If it still fails please consider contacting your support centre for further assistance.

[kleankutken]

Never mind.  I am boxing it back up and returning it.

[kleankutken]

I just received this printer.  The power button does not do anything.  I plugged and unplugged power cord several times.  After one of these times the panel lit up with the words PLEASE WAIT.  After a few seconds a click noise was heard and the panel became unlit....you could still hear some fan(s) running.  Again, the power switch does nothing so I unplug again and after several more attempts the panel stays lit, goes through the brief setup and I print a test page.  I began printing some postcards and foolishly? waited 2 minutes between printing.  The printer went to sleep and won't wake up.  In control panel it will say that the printer is offline.  This is just one of several issues with this new printer.  Anyone have some ideas on what is happening?  Thanks.