cancel
Showing results for 
Search instead for 
Did you mean: 
Keave
FreeFlow User

a few topic regarding D125 Printer

I have a few question regarding D125 Printer functionalty:

- what is the final software version for IOT and where is it available

- how to modify default value (5) for folding option without stapling for booklet creation

- how to modify defauls margins (imageable area) - 4mm to 0 mm

0 Kudos
6 Replies
Analyst Nation Moderator Joe053204-hcl
Analyst Nation Moderator

Re: a few topic regarding D125 Printer

1. 25.13.63 (1.204.121) It isn't available on public links, so you need to call Xerox to get it.

2. It's done via NVM changes, which requires Diagnostics mode access, so it can't be posted here, you will need to have a tech visit

3. You can't. Xerox does not make borderless devices

 

Please be sure to select "Accept Solution" and or select the thumbs up icon to enter Kudos for posts that resolve your issues. Your feedback counts!

Joe
0 Kudos
Keave
FreeFlow User

Re: a few topic regarding D125 Printer

Thanks Joe.

Could you please confirm if 25.x is correct version for Printer model (not 26.x)?

At this moment we have 26.11.83 (System), 1.204.110 (Controller), 82.21.0 (IOT ROM), 13.8.0 (HCF ROM), 5.29.0 (Finisher ROM) and 3.0.18 (SJFI). 

About booklet finisher possibilities - could you please tell me what is the value we should put in NVM (what is the NVM number) to increase that value to maximum (hope it is 25 sheets like for booklet creation - folding with stapling)? I know how to enter to Diagnostic Mode (I'm Xerox employee) on that machine.

I heard that it is possible to change some NVM (but I don't know which one) to minimize the margins but I don't know if it is possible to set it to 0. I understand that it is not possible based on your knowledge? In Nuvera you have possibilities to print to edge. I will appreciate any help.

Kind regards, Krystian

0 Kudos
Analyst Nation Moderator Joe053204-hcl
Analyst Nation Moderator

Re: a few topic regarding D125 Printer

25.13.63 is fromNovember 2016

26.11.83 is from October 2012

 

I don't know the NVM changes required.

 

Yes, Nuvera can have the border set to 0mm by the SA, but not the end user due to the issues it causes, Xerox will not allow the "how to" to be released to the end user because when issues occur, they want to have the paper work showing you agreed to it.

 

 

Please be sure to select "Accept Solution" and or select the thumbs up icon to enter Kudos for posts that resolve your issues. Your feedback counts!

Joe
0 Kudos
Keave
FreeFlow User

Re: a few topic regarding D125 Printer

Joe, to understand correctly - now there is common patches program for Copier/Printer and Printer models of D-series and the latest version is 25.13.63 (or even 25.13.93)?
About the margins - fully agree with you, in CED for Nuvera is wrote that 3 mm border guarantee you the image quality but you can change it to 0 but to have in mind that an quality issue may occure at this area. Is there similar solution for D-series devices?
0 Kudos
Analyst Nation Moderator Joe053204-hcl
Analyst Nation Moderator

Re: a few topic regarding D125 Printer

I don't know of a 25.13.93, could have been a one-off I suppose, it is not on the Software configuration charts (I can't provide that document, it is internal only)

 

I have never seen one for the D series, this doesn't mean it doesn't exist though, I never supported D-series, I just did the 2101/4110/4127/4595 etc for a few years, they definitely did not.

 

 

Please be sure to select "Accept Solution" and or select the thumbs up icon to enter Kudos for posts that resolve your issues. Your feedback counts!

Joe
0 Kudos
Keave
FreeFlow User

Re: a few topic regarding D125 Printer

Joe, can you share this document and link to place where is stored normaly to this e-mail address: krystian.zielinski@xerox.com?

0 Kudos